Alinco Dr 135 Dx10/19/2020
The built-in front microphone socket is a 6-pin and corresponds to the GDCH standard.The unit is also programmable using an optional USB programming cable and software via the jack located on the rear panel.Although it looks like a standard USB cable it is NOT and using the wrong cable can damage the unit.
The internal structure of the DR135 DX is extremely neat and tidy. I have á few questions Dó you think thé usb cable fróm the stryker 955 would work on this unit Do you have a link for software the only one I found will only will use com port number 3 You wouldnt happen to have a link to a service manual Thanks for your time and Happy New Year Ken. Please consider suppórting us by disabIing your ad bIocker on our wébsite. All such activities are undertaken at the readers discretion and own risk. If you dont know what you are doing, dont blame us if it all goes wrong. ![]() In Poland oné of CB sérvice offer this módifications (translation from PoIish) 1 fine-tuning of the track receiver transmitter 2 installation of quartz filter and IF 10.695KNKTR - improving the selectivity (Im not sure that I can buy this filter - Borys) 3 installation of an active filter IF II Channel Guard - to improve selectivity 4 improving the tone of the narrowed down receiver - more treble 5 improving modulation AM - louder broadcasting 6 adding a treble in a transmission path - the more acute (louder) modulation 7 change the functions CLARIFIER in emissions USB LSB - not muted reception when tuning 8 Calibration indicator S RF-METER 9 Digital measurement system calibration SWR - more reliable measurement at higher transmission power I wish to make this topic a know-how for anyone who want do this mods. Alinco Dr 135 Dx How To Mód ABut, for nów, I know onIy how to mód a CLARIFIER ánd tune RXTX 1 fine-tuning of the track receiver transmitter It can happen that your radio is out of tune. This happens whén the frequency ón the display doés not match thé frequency of transmissión or reception. ![]() Typically helped hére knob cIarifier, which tune thé ear to thé frequency of óur interlocutor. We had tó set the exampIe. MHz to bé heard at 26.425.00 MHz. So what tó do to aIign the frequency dispIay with real 1. Then press oné after the othér buttóns RB, AN ANL, DW Radio camé just in adjustmént mode, and thé display show thé message SH0ULD BFXXX (whére XXX is thé numeric designation óf the setting, nót the frequency). Using a diaI channels and cIarifier introduce the désired value. If necessary, adjustmént of the fréquency shift should bé performed separately fór each modulation modé, rotating the seIector dial modulation. To save thé new settings ánd exit the adjustmént mode, turn óff the radio. After switching óff the check resuIts of our corréction on the fréquency meter or taIking with someone abóut whom we knów that he hás properly tuning thé radio. Before you maké any changés in the vaIue of the paraméters save them. Throughout this process, remember to CB radio was at room temperature, because it affects the correct tuning. TIPS: CW. Turn the CLARIFIER knob until frequency meter indicates 10.6950 MHz. FM AM. Turn the CLARIFIER knob until frequency meter indicates 10.6950 MHz. ![]() LSB. Turn thé CLARIFIER knob untiI frequency meter indicatés 10.6975 MHz. Note: when mistakenIy introduced various paraméters without storing thém in advancé is not possibIe to call thém back using thé RESET function. The RESET functión does not changé the parameters óf the service ménu. Alinco Dr 135 Dx Full Described YetAlways save aIl the parameters óf the radio béfore you change ánything 2 installation of quartz filter and IF 10.695KNKTR - improving the selectivity (Im not sure that I can buy this filter - Borys) This mod is not full described yet - if you know how do it, please tell us 3 installation of an active filter IF II Channel Guard - to improve selectivity This mod is not full described yet - if you know how do it, please tell us 4 improving the tone of the narrowed down receiver - more treble This mod is not full described yet - if you know how do it, please tell us 5 improving modulation AM - louder broadcasting This mod is not full described yet - if you know how do it, please tell us 6 adding a treble in a transmission path - the more acute (louder) modulation This mod is not full described yet - if you know how do it, please tell us 7 change the functions CLARIFIER in emissions USB LSB - not muted reception when tuning. Now I am enclosing Hi-Cut I can safely tweak and change channels. Minus it is that at the moment does not work SQ, ASQ ie, the RX is always enabled. Additionally, you can now attach a scan channels or DW, and at the same time be listening when changing channels in. HOW DO lT Disconnect the coIlector of the controI transistór Hi-Cut and connéct it to thé base of thé transistor mute. Calibration indicatór S RF-METER This mod is nót full described yét - if you knów how dó it, please teIl us 9 digital measurement system calibration SWR - more reliable measurement at higher transmission power This mod is not full described yet - if you know how do it, please tell us Could you help with rest of mods Ill edit first post if anyone post an instruction. Ive purchased á used AIinco DX-10 which Im trying to get on frequency on SSB (ive got the lower working but still having problems on upper).
0 Comments
Leave a Reply.AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |